Book My Estimate

 

 

Just how do you actually feel when it comes to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?

Mounting a tub isn't precisely rocket science, however it does need solid plumbing, carpentry, and in some cases, tiling abilities. Replacing an old bathtub with a new one is additionally a reasonably difficult task. If the old tub is easily accessible, the task can move immediately; if you have to open a wall to remove the old bathtub and position the brand-new bathtub, the job is a lot harder. In either instance, the job is within a home handyman's abilities, although you will need an assistant to vacate the old tub and also embeded in the new one. See to it you have qualified yourself for the work and also fit trying it. Instead of hiring a professional to take control of a halfway-completed job, it is much better to consider using one before you start. Possibilities are you may require a professional plumber to make tube connections.
This post will aid you mount a new bath tub in your restroom if you have currently purchased a brand-new tub and do not need to change the arrangement of your previous water pipelines.
Your devices and also material list should consist of the following:

 

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Chisel


• Measuring tape


• Pipe Caps


 

Removing Old Taps

If you require to change old taps with brand-new ones as a part of your installation, then the first thing you must do is separate the water supply. After doing so, activate the taps to drain pipes any type of water staying in the system. The procedure of eliminating the existing taps can be rather problematic because of the restricted access that is often the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will originate from the pipelines. When the supply pipelines have been gotten rid of, utilize the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary taps from turning throughout this process. When the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing substance.
Before carrying on to fit the brand-new taps, contrast the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.

 

 

Suitable New Touches

If the tails of the brand-new taps are plastic, then you will certainly require a plastic adapter to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the other end provides a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, position the faucet in the installing opening in the bath/basin guaranteeing that the washing machines remain in place in between the faucet and the sink. Safeguard the faucet in position with the manufacturer offered backnut. Once the faucet is firmly in place, the supply pipes can be attached to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal faucet connectors. The former kind ought to be connected to the faucet finishes first, tightening up just by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been connected.

 

 

Setting up the Bath tub

Using the two wood boards under its feet, place the tub in the called for position. The wood boards are useful in equally spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto four little factors.
The next goal is to make sure that the bath tub is leveled all round. This can be achieved by checking the spirit level as well as changing the feet on the tub up until the level reviews degree.
To set up taps, fit the bottom of the furthest versatile tap port to the suitable supply pipe by making a compression join; then do the exact same for the other tap.
Turn on the water system as well as inspect all joints as well as new pipework for leaks and tighten them if necessary. Fill the tub and additionally examine the overflow outlet as well as the normal electrical outlet for leaks.
Lastly, deal with the bathroom paneling as defined in the maker's user's manual. Tiling as well as securing around the tub ought to wait up until the bathtub has actually been used at least when as this will certainly resolve it right into its last setting.

 

 

Planning for the Installment

To start with, the supporting frame supplied with the bath must be fitted (if needed) according to the producer's directions. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is essential to ensure that if the faucet comes with a plastic washing machine, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is additionally practical to fit a sustaining plate under the faucets unit to prevent pressure on the tub.
Fit the versatile faucet adapters to the bottom of both taps using 2 nuts and olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet with the hole in the bathroom. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. See to it you utilize every one of the provided washing machines.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath ought to now be ready to be suited its final position.

 

 

Tiling Around the Bathtub

In the location where the bathroom fulfills the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to crack an inflexible seal, triggering the water to permeate the wall surface in between the bath and also the tiling, causing difficulties with wetness and feasible leaks to the ceiling below.
You can pick from a range of coloured sealants to blend in your components and installations. They are sold in tubes and cartridges, and also can sealing gaps approximately a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of soaked paper or soft rope. Keep in mind to always load the tub with water prior to securing, to allow for the activity experienced when the bathtub is in usage. The sealant can fracture rather early if you do not consider this movement prior to securing.
Additionally, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also conveniently readily available on the market. It is advisable to fit the floor tiles utilizing waterproof or water resistant adhesive and also grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

As a keen person who reads about How to Install a Bathtub Yourself, I think sharing that short article was smart. Sharing is caring. Helping others is fun. Thank you for taking the time to read it.

Visit Website